HPSSSB Hamirpur Junior Engineer (Civil) screening test held on 10 August 2021 (Code C-764/2021, Series B, 170 questions): fluid mechanics, hydrology and irrigation, structures, RCC and steel design, soil mechanics, surveying, highways, environmental engineering, building materials, estimating, general knowledge, H.P. GK and English. All 170 questions are included, including the Hindi language section (Q134–137). No official answer key for this paper is available, so the answer key was prepared by Raman Academy and checked against standard civil engineering references.
Results
#1. In the mid-section formula
#2. To keep the intensity of bearing pressure between the column base and concrete compressive throughout the length of the column base, the ratio of the moment M to axial load P should be
#3. The centrifugal force due to curvature of track is assumed to act on the bridge at a height of
#4. Minimum pitch provided in riveted steel tanks is (where d is diameter of rivets)
#5. If the gross vehicle weight of a truck is 30 tonne and rolling resistance is 30 kg/tonne, then the tractive effort required to keep the truck moving at a uniform speed is
#6. A machine costs ₹20,000 and its useful life is 8 years. The money is borrowed at 8% interest per annum. The capital recovery factor at 8% interest per annum for 8 years is 0.174. The annual equipment cost of the machine will be
#7. The original cost of an equipment is ₹10,000. Its salvage value at the end of its total useful life of five years is ₹1,000. Its book value at the end of two years of its useful life (as per straight line method of evaluation of depreciation) will be
#8. An earth moving equipment costs ₹5,00,000 and has an estimated life of 10 years and a salvage value of ₹50,000. What uniform annual amount must be set aside at the end of each of the 10 years for replacement if the interest rate is 8% per annum and if the sinking fund factor at 8% per annum interest rate for 10 years is 0.069?
#9. Ratio of permissible stress in direct compression and bending compression is
#10. If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, 6 kg, 4 kg respectively, the fineness modulus of the aggregate is
#11. A continuous beam is deemed to be a deep beam when the ratio of effective span to overall depth (l/D) is less than
#12. Two columns 50 cm × 50 cm and 60 cm × 60 cm carry 80 tonnes and 120 tonnes of loads respectively. The centre to centre distance between columns is 5.00 metres. The permissible bearing capacity of the soil is 20 t/m². If the footing is not to project more than 25 cm beyond the outside of the smaller column, pick up the correct design parameters of the footing from the following:
#13. In places where the soil is soft and has small resistance to the flow of concrete, which one of the following types of piles is used?
#14. The additional piles which are driven to increase the capacity of supporting loads on vertical piles are known as
#15. Duco is one of the patent forms of
#16. The law of Polygon of Forces states that
#17. If a body is lying on a plane whose inclination with the horizontal is less than the angle of friction, then (i) a force is required to move the body upwards (ii) a force is required to move the body downward (iii) the body will not be in equilibrium. The correct answer is
#18. A load of 500 kg was lifted through a distance of 13 cm by an effort of 25 kg which moved through a distance of 650 cm. The velocity ratio of the lifting machine is
#19. From a solid cylinder of height 8 cm and radius 4 cm, a right circular cone is scooped out on the same base and having the same height as that of the cylinder. The C.G. of the remainder is at a height of
#20. One end of a light string 4 m in length is fixed to a point on a smooth wall and the other end fastened to a point on the surface of a smooth sphere of diameter 2.25 m and of weight 100 kg. The reaction between the sphere and the wall of the arrangement made is
#21. A flow through long pipe at constant rate is called
#22. A foundation is called shallow if its depth is
#23. A fall in a canal bed is generally provided, if
#24. In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called
#25. A cantilever carries uniformly distributed load W over its whole length and a force W acts at its free end upward. The net deflection of the free end will be
#26. Hydrographic surveys deal with the mapping of
#27. The minimum water content at which the soil just begins to crumble when rolled into threads 3 mm in diameter, is known as
#28. A standard oedometer test in the laboratory indicated that a 0.02 m thick clay specimen took 1.0 day to undergo 90% consolidation. How many days would a 2.0 m thick identical clay sample sandwiched between sand layers and subjected to an identical stress increment take to undergo the same?
#29. Given the atomic weight of Fe is 56 and that of C is 12, the weight percentage of carbon in cementite (Fe3C) is
#30. A nozzle situated at a distance of 1 m above the ground level is inclined at an angle of 45° to the horizontal. The diameter of the nozzle is 50 mm and the jet of water from the nozzle strikes the ground at a horizontal distance of 4 m. Find the approximate rate of the flow of water.
#31. Match List-I with List-II: A. Deep tube well, B. Shallow tube well, C. Deep open well, D. Shallow open well with 1. Wind Power (Mill), 2. Submersible pump, 3. Persian wheel, 4. Centrifugal pump
#32. A circular segmental three-hinged arch of span 28 m and a rise of 4 m is hinged at the crown and springings. It carries a horizontal load of 100 N/m covering the full height of the arch on the right side. The horizontal thrust on the left spring will be
#33. Green house gas effect is caused by
#34. Which chlorine compound is used for the disinfection of municipal supply water?
#35. A wall of 200 mm thickness has an outside surface temperature of 50 °C and inside temperature of 25 °C with thermal conductivity of 0.51 W/m-K. The heat transfer through this wall will be
#36. Which of the following fluids can be classified as non-Newtonian? (1) Kerosene (2) Diesel oil (3) Human blood (4) Toothpaste (5) Water
#37. As the depth of immersion of a vertical plane surface increases, the location of centre of pressure
#38. When a simply supported rectangular beam is loaded transversely (downward), the maximum compressive stress develops on
#39. The soils in India (IS 1498) are classified according to (a modified)
#40. A homogeneous prismatic simply supported beam of length l, width B and depth D is subjected to a vertical point load P. The load can be placed anywhere along the span of the beam. The maximum flexural stress developed in the beam is
#41. A road is being designed for a speed of 110 km/hr on a horizontal curve with a super elevation of 8%. If the coefficient of side friction is 0.10, the minimum radius of the curve (in m) required for safe vehicular movement is
#42. A cantilever beam of length L carries a uniformly distributed load of intensity q. What will be the length of the plastic zone when the maximum bending moment equals the plastic moment Mp? (assume My/Mp = f)
#43. If Froude number is less than 1, the flow is called
#44. The intensity of irrigation for the Kharif season is 40% for an irrigation project with culturable command area of 25000 hectares. The duty for the Kharif season is 1000 hectare/cumec. Assuming transmission loss of 20%, the required discharge (in cumec) at the head of the canal is
#45. The Cipoletti weir is a ____ weir.
#46. A piece of wood having weight 5 kg floats in water with 60% of its volume under the liquid. The specific gravity of wood is
#47. The flow in which the velocity vector is identical in magnitude and direction at every point, for any given instant, is known as
#48. Which of the following sights will be applicable for a change point?
#49. The process of determining the location of the station (on the map) occupied by the plane table is called as
#50. 10.0 m³/s of water is diverted to a 30.0 hectare field for 4.0 hours. Soil probing after irrigation showed that 0.2 m of water had been stored in the root zone. Water application efficiency in this case will be
#51. Which of the following is not a major type of storm precipitation?
#52. Poise has a unit of
#53. Acoustics of an auditorium is considered to be excellent when its reverberation time is between
#54. What is the depth of water seal in traps?
#55. Find the Young’s Modulus of a brass rod having cross-sectional area 200 mm² and of length 300 mm which is subjected to a tensile load of 200 kN when the extension of rod is 0.3 mm.
#56. Which is the most common cause of acidity in water?
#57. The ultimate BOD value of a waste
#58. The amount of bleaching powder containing 10% available chlorine needed to chlorinate a rural supply covering a population of 10000 at 50 L pcd at the rate of 3 ppm is
#59. A position dependent force, F = 3x – 2 + 5x² N acts on a small body of mass 2 kg and displaces it from x = 0 to x = 2 m. The work done in joules is
#60. A ball is dropped from a spacecraft revolving around the earth at a height of 120 km. What will happen to the ball?
#61. A relation between g, t, m, l and v is expressed as (g²t⁴)/(ml²) = Kv², where g is acceleration, t is time, m is mass, l is length and v is velocity. The unit of K in S.I. units will be
#62. The centre of gravity of a quadrant of a circle lies along its central radius at a distance of
#63. Heat Island means
#64. A 20.0 cm long capillary tube is dipped in water. The water rises up to 8 cm. If the entire arrangement is put in a freely falling elevator, the length of the water column in the capillary tube will be
#65. In an aerial photogrammetric survey, if the exposure interval is 20 seconds to cover ground distance of 1000 m between exposures, what would be the ground speed of the aircraft?
#66. A Vernier scale in which 10 divisions of the Vernier scale is equal to 9 divisions of the main scale is called
#67. A 50.00 cm square bearing plate settles by 10 mm in the plate load test on cohesionless soil, when the intensity of the loading is 200 kN/m². What will be the settlement of a shallow foundation of 1.3 m square under the same intensity of loading?
#68. The optimum depth of kor watering for a rice crop is
#69. The slow setting cement will have higher percentage of
#70. Coal-tar is obtained by destructive distillation of
#71. Painting works are measured in terms of
#72. The main constituent of varnish is
#73. Gypsum is added in cement
#74. Hollow bricks are mainly used for
#75. The average life of timber used in exposed environment is
#76. A temporary structure to support an arch during construction is called
#77. The height of hand railing above the tread should be generally in between
#78. For a bridge pier, in very deep water the foundation to be used should be
#79. The development of one or more local swellings on the finished plastered surface is called
#80. Highest value of Poisson’s ratio may be expected for
#81. Among the following mild steel sections, the most economical section (for flexure) is
#82. Vacuum pressure is equivalent to
#83. When a rectangular beam is loaded longitudinally, shear develops on
#84. Attraction between molecules of a liquid (say water) and that of solid boundary surface (say glass) in contact with liquid is called
#85. At sea level under normal conditions the atmospheric pressure is 10.3 metres of water and its equivalent height of mercury will be
#86. At vena contracta a jet has the minimum area of cross-section and so the velocity of liquid jet at this section will be
#87. A differential free swell test on a soil gives a value of differential free swell of 25%. What is the degree of swelling (expansiveness)?
#88. Agriculture University Palampur is named after which personality?
#89. Roerich Art Gallery is located at which place of H.P.?
#90. Jararphuki marriage is prevalent among the tribal people of which districts of H.P.?
#91. Which Viceroy named his daughter after the Naldehra?
#92. Which sage has been associated with Rewalsar in district Mandi, H.P.?
#93. Mindal Devi temple is situated at which place in H.P.?
#94. Dal fair is celebrated at which place in H.P.?
#95. The Rasa dance is prevalent in which district of H.P.?
#96. HRTC came into existence in which year?
#97. Simbalbara National Park is situated in which district of H.P.?
#98. Who was the first Chairman of H.P. Administrative Tribunal?
#99. Founder of Kunihar dominion was
#100. Mandi state was an offshoot of which Princely State?
#101. Which valley is also known as Baspa valley?
#102. Indrahar pass connects Kangra district with which place of H.P.?
#103. Which country launched the ‘Project O2 for India’ to tackle the medical oxygen demand after Covid-19 second wave (2021)?
#104. Naftali Bennett, who was in news in 2021, became the Prime Minister of which country?
#105. Abdulla Shahid, president-elect of the 76th session of the U.N. General Assembly, is from which country?
#106. ‘BE’ is related to ‘GJ’ in the same way as ‘PS’ is related to
#107. If ice is called water, water is called rain, rain is called wind, wind is called air and air is called sky, then you will find amphibians on land and in
#108. Raju goes for a walk on every Monday, Wednesday and Saturday and Santosh goes for a walk at the same time on every Monday, Thursday, Friday and Saturday. How many times will they meet during the month of September if the month begins on Tuesday?
#109. In a row of 40 students facing North, Kailash is 6th to the left of Soman. If Soman is 30th from the left end of the row, how far is Kailash from the right end of the row?
#110. Which destroys worn out RBCs in the human body?
#111. Penicillin is produced from
#112. Mica is used in an electric iron because it is a
#113. Aspirin is the common name of
#114. Rigveda Samhita denotes one fourth of its hymns to
#115. Before ascending the Maurya throne, Ashoka served as a Viceroy of
#116. Banda Singh Bahadur was executed by the orders of which emperor?
#117. Battle of Khanwa was fought between
#118. Which was written by Raja Rammohan Roy?
#119. The first Governor General of India was
#120. Which part of the Indian Constitution deals with the Directive Principles of State Policy?
#121. A person who is not a member of parliament can be appointed as a Minister by the President for a maximum period of
#122. A judge of the Supreme Court can be removed from office only on grounds of
#123. When did India become a member of the IMF?
#124. The term used to describe a situation of decrease in the general price of goods and services is
#125. The Saturn rings were discovered by
#126. The International Date Line does not cut Fiji Islands to keep the same day as in
#127. Which atmospheric layer lies closely above the troposphere?
#128. Amman is the capital of which country?
#129. Which wild life sanctuary is situated in Assam?
#130. Synonym of ‘Solicit’ is
#131. One word substitution for ‘A name adopted by an author in his writings’ is
#132. There being no evidence against him, he was acquitted ____ the charge.
#133. Meaning of the idiom ‘To cool one’s heels’ is
#134. ‘तपोवन’ का संधि विच्छेद है
#135. ‘नीलकमल’ में समास है
#136. ‘राष्ट्रीय’ में प्रत्यय है
#137. ‘कांसा’ का पर्यायवाची है
#138. If the magnetic bearing of the sun at a place at noon in southern hemisphere is 167°, the magnetic declination at that place is
#139. The R.L. of the point A which is on the floor is 100 m and back sight reading on A is 2.455 m. If the foresight reading on the point B which is on the ceiling (inverted staff) is 2.745 m, the R.L. of point B will be
#140. In the cross-section method of indirect contouring, the spacing of cross-sections depends upon (i) contour interval (ii) scale of plan (iii) characteristics of ground. The correct answer is
#141. Two bars of different materials are of the same size and are subjected to same tensile forces. If the bars have unit elongations in the ratio of 4 : 7, then the ratio of moduli of elasticity of the two materials is
#142. A beam of overall length L, with equal overhangs on both sides, carries a uniformly distributed load over the entire length. To have numerically equal bending moments at centre of the beam and at supports, the distance between the supports should be
#143. When the width of car parking space and width of street are limited, generally preferred parking system is
#144. Penetration test on bitumen is used for determining its
#145. In soils having same values of plasticity index, if liquid limit is increased, then
#146. The most economical lighting layout which is suitable for narrow roads is
#147. Speed regulations on roads is decided on the basis of
#148. If the coefficient of friction on the road surface is 0.15 and a maximum super-elevation 1 in 15 is provided, the maximum speed of the vehicles on a curve of 100 metre radius is
#149. In CBR test the value of CBR is calculated at
#150. The thickness of boundary layer at the leading (entrance) edge will be
#151. The total length of valley formed by two gradients -3% and +2%, curve between the two tangent points to provide a rate of change of centrifugal acceleration 0.6 m/sec³, for a design speed 100 kmph is
#152. Minimum radius of a simple circular curve deflecting through 5°, is
#153. At a road junction, 16 cross conflict points are severe, if
#154. RC-2, MC-2 and SC-2 correspond to
#155. Three points A, B and C 500 m apart on a straight road have 500 m, 505 m and 510 m as their reduced levels. The road is said to have
#156. The field capacity of a soil is 25%, its permanent wilting point is 15% and specific dry unit weight is 1.5. If the depth of root zone of a crop is 80 cm, the storage capacity of the soil is
#157. The water face of the guide banks is protected by
#158. If the optimum depth of kor watering for a crop is 15.12 cm, the outlet factor for the crop for four week period in hectares per cumec is
#159. A deficit of sediments in flowing water may cause a river
#160. If the irrigation efficiency is 80%, conveyance losses are 20% and the actual depth of watering is 16 cm, the depth of water required at the canal outlet is
#161. A ship whose hull length is 100 m is to travel at 10 m/sec. For dynamic similarity, at what velocity should a 1 : 25 model be towed through water?
#162. The total pressure on the surface of a vertical sluice gate 2 m × 1 m with its top 2 m surface being 0.5 m below the water level will be
#163. An odd shaped body weighing 7.5 kg and occupying 0.01 m³ volume will be completely submerged in a fluid having specific gravity of
#164. With an increase in size of tube, the rise or depression of liquid in the tube due to surface tension will
#165. In order to avoid tendency of separation at throat in a Venturimeter, the ratio of the diameter at throat to the diameter of pipe should be
#166. If a body floating in a liquid occupies a new position and remains at rest in this new position when given a small angular displacement, the body is said to be in ____ equilibrium.
#167. True one-dimensional flow occurs when
#168. An internal mouthpiece is said to be running ____ if the length of the mouthpiece is more than three times the diameter of the orifice.
#169. A flow in which each liquid particle has a definite path, and the paths of individual particles do not cross each other, is called
#170. The ground surface slopes (falls) 1 in 50 along a proposed railway embankment 150 m in length. The height of the embankment at zero chainage is 0.5 m, the width is 11 m and side slopes 2:1. If the falling gradient of the embankment is 1 in 150, the quantity of the earthwork calculated by Prismoidal formula is

