HPSSSB Junior Engineer (Civil) Previous Year Question Paper – 2014

by

HPSSSB Hamirpur Junior Engineer (Civil) screening test of 2014 (Code C-231/2014, Series A): structures, RCC and steel design, surveying, fluid mechanics, soil mechanics, irrigation, transportation, estimating, building materials, general knowledge, H.P. GK and English. 195 of the 200 questions are included, including the Hindi language section (Q161–170); Q196–200 are missing from the available copy of the paper. No official answer key for this paper is available, so the answer key was prepared by Raman Academy and checked against standard civil engineering references.

 

Results

#1. Poisson’s ratio is defined as the ratio of

#2. Hardy-Cross method is nothing but

#3. For a rectangular section the maximum shear stress due to bending is

#4. Slenderness ratio is defined as the ratio of the length of the column to its

#5. Materials which have an appreciable deformation before failure are said to be




#6. The equivalent value of a pressure of 1 kg/cm² in terms of the height of water column is

#7. A compound pipe system consists of 1800 m of 50 cm, 1200 m of 40 cm and 600 m of 30 cm cast iron pipes connected in series. If this system is converted into an equivalent length of 40 cm pipe, the length will be

#8. For sub-critical flow or tranquil flow to exist, the Froude number should be

#9. A natural soil deposit has a bulk density of 1.88 g/cm³ and water content of 5%, then the dry density of soil is equal to

#10. Well in a confined aquifer is called




#11. In his analysis Terzaghi considered

#12. A two hinged arch is

#13. A mix having cement, fine aggregate and coarse aggregate in the ratio of 1:2:4 approximately corresponds to the grade

#14. In the case of over reinforced section

#15. Minimum tensile reinforcement in a singly reinforced beam shall not be less than




#16. In the design of water tanks, the minimum reinforcement required for members having thickness up to 100 millimeter is

#17. A series of closely spaced contour lines represent a

#18. In the case of a truss, minimum number of rivets required for the connection of a member to a gusset plate is

#19. A timber column is said to be a short one if l/d ratio

#20. Duty of water for a crop requiring more water is




#21. In a multipurpose project, the dead storage is provided for the purpose of

#22. Capacity of an irrigation tank depends on

#23. Specific gravity of a good stone suitable for structural purposes

#24. The Vee-bee test is used to determine

#25. Magnetic properties can be produced by adding one of the following to high carbon steel




#26. Contour lines of different elevations cannot cross each other except in case of

#27. The object of back sight is

#28. The R.L. of a Station A is 100.0 m and B.S. at A is 3.0 m. The F.S. at Station B is 2.0 m, the R.L. of Station B is

#29. The F.B. of a line is N 30° E, its B.B. would be

#30. Error in chaining will be cumulative, + in case of




#31. Box sextant may be used as

#32. A temporary support provided to prevent the soil from falling into the trench is known as

#33. To construct a wall in Single Flemish Bond, the minimum thickness of the wall should be

#34. A document containing detailed description of all the items of work (but their quantities are not mentioned) together with their current rates is called

#35. For estimating purposes, the quantity of steel per m³ of concrete is taken as




#36. Air relief valves are provided at

#37. As per IRC, the ruling gradient of a road in plains is

#38. The process of roughening of solid backgrounds to provide suitable bond or key for plastering is called

#39. Sewage contains

#40. In two way slabs, reinforcement in short span is placed ____ the reinforcement in the long span.




#41. In limit state method of design, the compressive strength of concrete in the structure is assumed to be

#42. The minimum land width required for NH in rural areas is

#43. 1435 mm gauge (in railways) is known as

#44. The first signal met by a train approaching a station is called

#45. A railway track is elastic mainly because of




#46. A soil sample has a porosity of 40 percent, the specific gravity of solids is 2.7. If the soil is 50% saturated, unit weight of the soil is

#47. What will be the H.P. required to lift water from a total height of 20.0 m at the rate of 75 lit/sec (Neglecting losses)?

#48. Fore bearing of a line is 170°, the back bearing of the line would be

#49. Turpentine oil in paint is used as a

#50. Knot is a defect in




#51. If ‘d’ be the diameter of MS or tor steel bars in mm, the standard weight (in kg) per metre of the bar is

#52. The shear force diagram for a cantilever beam subjected to a concentrated load at the free end is given by a/an

#53. Of the several prismatic beams of equal length and of same material, the beam that can carry maximum load in flexure is the one having maximum

#54. The maximum pitch of rivets for parts in tension in the direction of stress should not exceed, whichever is less

#55. With a percentage increase of carbon in steel, decreases its




#56. The permissible stress in axial compression proposed in IS:800-1984 is based on

#57. The economical spacing of roof truss is

#58. In rolled steel beams, shear force is mostly resisted by

#59. The maximum shear stress of steel beams shall not exceed (IS 800-1984)

#60. The brick work is measured in sq metre, in case of




#61. For 12 mm thick cement plastering 1 : 6 on 100 sq.m new brick work, quantity of cement required is

#62. The maximum area of tension reinforcement in beams shall not exceed

#63. The number of treads in a flight is equal to

#64. The transverse reinforcements provided at right angles to the main reinforcement

#65. If T and R are tread and rise respectively of a stair (in cm), then




#66. In a prestressed beam carrying an external load W with a bent tendon having angle of inclination θ and prestressed load P, the net downward load at the centre is

#67. Unit Hydrograph theory was enunciated by

#68. The coagulant widely used for sewage treatment is

#69. Self-cleansing velocity is

#70. The ratio of maximum sewage flow to average sewage flow for mains up to 1 m in diameter, is




#71. Pick up the correct equation from the following:

#72. The minimum recommended diameter of sewers is

#73. As per I.S. 456-1978, the pH value of water shall be

#74. Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by

#75. The percentage of minimum reinforcement of the gross sectional area in slabs, is




#76. Setting out a curve by two theodolite method, involves

#77. The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known

#78. A partially saturated sample of soil has a unit weight of 2.0 g/cm³ and specific gravity of soil particles is 2.6. If the moisture content in the soil is 20%, the degree of saturation is

#79. The continuous strain, which the concrete undergoes due to application of external loads is called

#80. A compaction factor of 0.75 indicates ____ workability.




#81. A concrete mass containing 5% of voids

#82. One cubic metre of cement weighs

#83. In Limit state method of design, the factor of safety for concrete and steel respectively are

#84. Bulking of sand takes place due to

#85. The proof stress in Steel is the stress corresponding to the strain of




#86. While compared with singly reinforced beams, the depth of doubly reinforced beam is

#87. Limit state of collapse deals with

#88. The development length of bars in compression is taken as

#89. Limiting moment of resistance of a singly reinforced section for Fe 500 grade steel is

#90. Pick up the correct statement from the following:




#91. Frederick W. Taylor introduced a type of organization known as

#92. The economic spacing of roof truss is given by (where t = cost of trusses/unit area, p = cost of purlins/unit area, r = cost of roof coverings/unit area)

#93. Trade name for white cement is

#94. Concrete whose slump value is equal to 65 mm is

#95. The 7 day compressive strength for M 15 grade of concrete on 15 cm cube shall not be less than




#96. Bulking of sludge is encountered in

#97. In a transit theodolite, error due to eccentricity of verniers is eliminated by reading

#98. The ratio of maximum velocity to average velocity of viscous fluid through a circular pipe is

#99. A fillet weld may be termed as

#100. The effective length of a compression member of length L held in position and restrained in direction at one end and effectively restrained in direction but not held in position at the other end, is




#101. The peak of 4 hour flood hydrograph is 240 m³/sec. If the rainfall excess is 8 cm and base flow which is constant is 40 m³/sec, then the peak of 4 hour unit hydrograph will be

#102. Agate cap is fitted with a

#103. If true bearing of a line AB is 269° 30′, then the azimuth of the line AB is

#104. The sensitivity of a bubble tube can be increased by

#105. Intersection method of detailed plotting is most suitable for




#106. In a Sarda type fall, rectangular crest is used for discharge upto

#107. Which of the following shapes is preferred in a valley curve?

#108. If in a Dorry abrasion test, the loss in weight is 21 gms, then the coefficient of hardness is

#109. The direct cost of a project with respect to normal time is

#110. Which of the following is a measure of particle size range?




#111. The moisture content in a well seasoned timber is

#112. The most common admixture which is used to accelerate the initial set of concrete is

#113. Pitched and sloping roofs are suitable in

#114. The height between two floors is 3.00 m and riser is 15 cm. Assuming two flights between the floors, the number of treads will be

#115. Shear stress on principal planes is




#116. The slenderness ratio of lacing bars should not exceed

#117. In order to obtain the best workability of concrete, the preferred shape of aggregate is

#118. Minimum thickness of load bearing RCC wall should be

#119. The bond strength between steel and concrete is due to

#120. According to IS: 456-1978, the maximum water-cement ratio in plain concrete to ensure durability in mild exposure is limited to




#121. The efficiency of the centrifugal pump used for lifting water from a tube well may be assumed to be

#122. The correction for the sag is

#123. Galvanizing means covering iron with a thin coat of

#124. For the movement of vehicles at an intersection of two roads, without any interference, the type of grade separator generally preferred is

#125. Irrigation canals are generally aligned along ____ line.




#126. The momentum correction factor (β) for the viscous flow through a circular pipe is

#127. Rails are bent to correct curvature if the degree of curve is more than

#128. For full face method, the excavation to be done is generally divided into

#129. For battened struts, the effective length is increased by

#130. Dado is usually associated with




#131. The transitional middle portion of a logistic curve follows

#132. When loads are applied proportionately to a frame structure containing members in one plane, the structure is called

#133. Beams composed of more than one material, rigidly connected together so as to behave as one piece are known as

#134. The cross-section of a standard fillet is a triangle whose base angles are

#135. Who gave the slogan ‘Dilli Chalo’?




#136. The religious book ‘Zend Avesta’ is associated with

#137. The last Maha Kumbha (2013) was held at

#138. ‘Digboi’ of Asom is associated with

#139. Which of the following crops need maximum water per hectare?

#140. Which of the following places is associated with ‘Char Minar’?




#141. If Cash Reserve Ratio (CRR) is lowered by the RBI, its impact on credit creation will be to

#142. In India ____ formulates the fiscal policy.

#143. The 15th IIFA awards ceremony was recently (2014) held at

#144. Rashtriya Indian Military College (RIMC) is located at

#145. Who among the following Hindu Gods, is also known as ‘Pashupati’?




#146. ‘Anirban Lahiri’ is associated with

#147. Choose the odd one out.

#148. Choose the odd one out.

#149. Choose the odd one out.

#150. Choose the odd one out.




#151. I saw a herd of cows ____ the field.

#152. The rule of law is applicable ____ everyone.

#153. Ram was accused ____ stealing his friend’s gold ring.

#154. The answer was written ____ red ink.

#155. Choose the word nearest in meaning to INTIMIDATE.




#156. Choose the word nearest in meaning to REACTION.

#157. Choose the word nearest in meaning to AMPUTATE.

#158. Choose the word opposite in meaning to PACIFY.

#159. Choose the word opposite in meaning to PLEASE.

#160. Choose the word opposite in meaning to DEPENDENCE.




#161. वर्तनी की दृष्टि से शुद्ध शब्द चुनिए :

#162. वर्तनी की दृष्टि से शुद्ध शब्द चुनिए :

#163. वर्तनी की दृष्टि से शुद्ध शब्द चुनिए :

#164. वर्तनी की दृष्टि से शुद्ध शब्द चुनिए :

#165. ‘अंगीकार’ का विलोम शब्द चुनिए :




#166. ‘खल’ का विलोम शब्द चुनिए :

#167. ‘भीषण’ का विलोम शब्द चुनिए :

#168. ‘सोम’ का सही पर्यायवाची शब्द चुनें :

#169. ‘शर’ का सही पर्यायवाची शब्द चुनें :

#170. ‘धेनु’ का सही पर्यायवाची शब्द चुनें :




#171. The district of Hamirpur was earlier a part of the erstwhile princely state of

#172. Which of the following is not a cantonment area?

#173. The Hindus identify ____ with ‘Lomasa Rishi’.

#174. The book ‘Kangra Paintings’ was written by

#175. ‘Kangra bride’ and ‘Gaddan’ are the famous paintings of




#176. Wazir Ram Singh Pathania belonged to the princely state of

#177. Who founded the town of Chamba?

#178. There is no hot water spring at

#179. The famous hotel Tripple ‘H’ (HHH) or the Hotel Holiday Home of HPTDC is located at

#180. ‘Tirthan’ sanctuary is located in the district of




#181. ‘Sentaroza’ (Santa Rosa) is the variety of

#182. Pandit Padam Dev was associated with

#183. As per census 2011, the density of population in Himachal Pradesh is ____ persons per sq. km.

#184. ‘Western Tragopan’ is commonly known as

#185. The famous peak ‘Shrikhand’ is located in the district of




#186. ‘Baralacha’ pass connects

#187. ‘Buddhil’ and ‘Siul’ are the tributaries of river

#188. Which of the following lakes is not an artificial (man-made) lake?

#189. ____ is famous for Asia’s largest fish breeding farm.

#190. ‘Ladarcha’ fair is associated with




#191. Himachal Pradesh has ____ seats in the Rajya Sabha.

#192. What is ‘Haar’?

#193. There are ____ phases of Chamera Hydroelectricity Project.

#194. ____ and ____ are famous for Resin and Turpentine producing industries.

#195. Bhuri Singh Museum is located at




Previous
Finish

Google search

Looking for More Resources?

Raman Academy ✕