HPSSSB Hamirpur Junior Engineer (Civil) screening test of 2017 (Code C-386/2017, Series D): fluid mechanics, hydrology and irrigation, structures, RCC and steel design, soil mechanics, surveying, highways, environmental engineering, building materials, general knowledge, H.P. GK and English. All 200 questions are included, including the Hindi language section (Q69–73). Answer key: the HPSSSB answer key (Post Code 529, Series D, 30.04.2017), followed for every question.
Results
#1. For a heavily reinforced concrete section the most suitable slump value (as per IS 456) will be
#2. The development length of bars as per IS-456 is given by (where σst = stress in bar, φ = dia. of bar, τbd = design bond stress)
#3. In reciprocal levelling between two points A and B on opposite banks of a river, the following staff readings were taken: with level at A — 1.500 on A and 1.00 on B; with level at B — 1.350 on A and 0.850 on B. If R.L. of A is 100.0 m, the R.L. of B
#4. With the rise of temperature, the sensitivity of bubble tube
#5. The length of a vertical curve connecting two uniform gradients of +0.8% and -0.6%, the rate of change of grade being 0.1% per 30 m, will be
#6. If L is the length of transition curve and R is the radius of circular curve, the shift of the curve is given as
#7. A negative declination shows that the magnetic meridian is to the
#8. The moisture content in a well seasoned timber is
#9. The pressure acting on the stones in stone masonry construction should be
#10. As compared to English bond, double Flemish bond is
#11. In any good staircase, the maximum and minimum pitch respectively should be
#12. Reinforced concrete slab acts as
#13. The relation between duty D in hectares/cumec, depth of water Δ in metres and base period B in days is given by
#14. Which of the following country is not a member of ASEAN?
#15. Who among the following is the author of the book ‘Life Divine’?
#16. 4G stands for
#17. ‘World Red Cross Day’ is celebrated every year on
#18. Pulitzer Prize is awarded for outstanding work in the field of
#19. Duleep Trophy is associated with the game of
#20. M.F. Hussain is also known as
#21. ‘Operation Blackboard’ aims at
#22. Nail polish remover contains
#23. Number of bones found in skull (neurocranium) is
#24. Haemophilia is a genetic disorder which leads to
#25. ‘Athlete’s foot’ is a disease caused by
#26. Which blood group is a universal recipient?
#27. Bamboo is classified as
#28. Which one of the following has the largest wavelength?
#29. Galvanized iron sheets are protected from rusting due to presence of a layer of
#30. Which of the following is used in oven?
#31. The Dynamo converts
#32. Disguised unemployment generally means that
#33. The main objective of the Twelfth Five Year Plan is
#34. Who was the Vice-chairman of NITI Aayog in 2017?
#35. Who is known as the father of ‘White Revolution’ in India?
#36. WTO came into existence at the conclusion of which round of GATT?
#37. The monetary and credit policy is announced by which of the following?
#38. The controlling authority of government expenditure is the
#39. The concept of Judicial Review in our Constitution has been taken from the Constitution of
#40. Right to Information in India is a
#41. The ideal of ‘Welfare State’ in the Indian Constitution is enshrined in its
#42. Who is competent to dissolve the Rajya Sabha?
#43. Which one of the following is the oldest mountain range in India?
#44. Sambhar Lake is nearest to which one of the following cities of Rajasthan?
#45. Which of the following is a popular folk dance of Maharashtra?
#46. Which among the following is best temple of Vijayanagar Art?
#47. Where was ‘Azad Hind Fauj’ set up?
#48. Who laid down the formation of modern postal system?
#49. Lal Chand Prarthi was born in which of the following district of Himachal Pradesh?
#50. Which one of the following is the first recipient of Param Vir Chakra in Himachal Pradesh?
#51. Himachal Pradesh Technical Education Board is located in
#52. Which one of the following district of Himachal Pradesh has the lowest literacy rate according to Census 2011?
#53. What is the rank of Himachal Pradesh as populous State of India as per Census 2011 amongst all States & Union Territories of India?
#54. Halda and Fagli festival is celebrated in
#55. In which year Himachal Pradesh became a Part ‘C’ State?
#56. Baira Siul Hydro Electricity Project is constructed across the tributaries of which river?
#57. In which of the following places has a breeding farm of Yak been established in Himachal Pradesh?
#58. Gumma and Darang are famous for
#59. Which of the following is in ‘Ramsar Site Wetland’ list?
#60. In a code ‘STATION’ is denoted by ‘URCRKMP’, then ‘BRING’ is denoted in the same code by
#61. Introducing a lady, a man said, “The only son of her father is my father”. How is the man related to the lady?
#62. Sarita is on 11th place from upwards in a group of 45 girls. If we start counting from downwards, what will be her place?
#63. Sehgal started to move in the direction of East and moved 6 m. Then he turned to his right and moved 6 m. After this he walked 20 m in the direction of North-West. Now how far is he from his starting point?
#64. I challenged him ____ a game of chess.
#65. This train is running ____ time.
#66. His services have been dispensed ____.
#67. I was delighted ____ your success.
#68. None ____ the brave deserve the fair.
#69. ‘पुत्री’ का पर्यायवाची नहीं है :
#70. ‘कामचोर’ में कौन सा समास है ?
#71. ‘अन्वय’ शब्द का संधि-विच्छेद है :
#72. शुद्ध शब्द चुनिए ।
#73. ‘लल्ला लोरी में आना’ मुहावरे का अर्थ है :
#74. In a linear reservoir, the
#75. In cements, generally the increase in strength during a period of 14 days to 28 days is primarily due to
#76. A beam of overall length l, with equal overhangs on both sides, carries a uniformly distributed load over the entire length. To have numerically equal bending moments at the centre of the beam and at its supports, the distance between the supports should be
#77. The specific gravity of commonly available ordinary Portland cement is
#78. In a section undergoing pure bending, the neutral surface is subjected to
#79. In columns, the minimum diameter of longitudinal reinforcement specified per IS 456:2000 is
#80. Total numbers of elastic constants of an orthotropic material are
#81. In this layer i.e. ____ cells become almost inactive and rigid as well as no sap is there and lying close to the core of tree, older in age.
#82. A material is incompressible. Its Poisson’s ratio will be
#83. A buttress in a wall is intended to provide
#84. In a combined footing for two columns carrying unequal loads, the maximum hogging moment occurs at
#85. In a simply supported beam of length 5 m, a unit moment in kN-m is applied at both ends in opposite direction. The magnitude of bending moment at centre will be
#86. Sand particles are made of
#87. A local soil with Ip = 15% is mixed with sand having Ip = 0. If Ip of mix is 6%, then the percentage of local soil in the mix is
#88. A line PQ in an old map had magnetic bearing of N 60°E when the magnetic declination was 2°E. If the magnetic declination is now 3°W, what would be the magnetic bearing of the line PQ now?
#89. In building construction, the place for providing damp-proof course is at
#90. Stress-strain curve of concrete (as idealised in IS 456) is
#91. In a pedestal, the factor by which the effective length shall not exceed the least lateral dimension is
#92. In a singly reinforced beam, if the permissible stress in concrete reaches earlier than the permissible stress in steel, the beam section is called
#93. What would be the safe stopping sight distance for a design speed of 50 km/h in two way traffic on a two lane road if the lag distance is 30 m and braking distance is 60 m?
#94. Prime coat is ____ viscous than tack coat and hence applied ____ tack coat.
#95. A homogeneous prismatic simply supported beam of length L, width B and depth D is subjected to a vertical point load P. The load can be placed anywhere along the span of the beam. The very maximum flexural stress developed in the beam is
#96. Which of the following is added for quick setting of cement?
#97. Slump test for concrete is carried out to determine its
#98. One cubic metre of mild steel weighs about
#99. In open channel flows, the characteristic length commonly used in defining the Reynolds number is the
#100. The water utilizable by plants is available in the form of
#101. For stability of floating bodies, metacenter should be
#102. If ‘p’ is the standard consistency of cement, the amount of water used in conducting the initial setting time test on cement is
#103. Recommended value of camber for thin bituminous surface is in the range
#104. If 375 g of water is required to have a cement paste 1875 g of normal consistency, the percentage of water is
#105. For an RCC structure, 100 cum concreting is done continuously. The minimum number of samples to be prepared for testing as per IS 456:2000 will be
#106. For concrete of grade M50, the value of flexural tensile strength will be nearly
#107. In case of highway construction, water bound macadam (WBM) grading No. 1 (G-I) consists of coarse aggregates in the range of
#108. Number of gram equivalents for 200 mg of calcium carbonate is
#109. Which of the following is not a source of permanent hardness in water?
#110. If residual strength is 40 kg/cm² and edge load stress is 20 kg/cm², what would be the factor of safety?
#111. Which of the following parameters is determined using Winkler’s method?
#112. Which of the following category of lakes has least level of productivity?
#113. A stress element is subjected to tensile stress of 5 MPa on both the principal planes. The radius of Mohr Circle corresponding to this element will be
#114. Void ratio of an undisturbed sample of soil is 0.6. The values of maximum and minimum possible void ratio are found as 0.8 and 0.4, respectively. The relative density, in percentage, for this soil sample will be
#115. Rate of super-elevation (as per IRC, e = V²/225R) for a horizontal curve of radius 100 m and design speed of 15 km/h, is
#116. Which of the following Hydrometer Correction factor is always additive in nature?
#117. Water content of a sample of soil is at the shrinkage limit. Which of the following parameters will not be affected by reduction in water content of soil?
#118. Main purpose(s) of seal coat is/are
#119. A steel truss consists of 9 members jointed together at 5 locations. This truss is
#120. A simply supported triangular truss ABC (supports at A and C) has a vertical member BD from apex B to D on the bottom chord AC. A 10 kN vertical load acts at B and there is no load at D. The force in member BD will be
#121. For a material, stress at proportionality limit is 200 MPa and modulus of elasticity is 200 GPa. The modulus of resilience for this material will be
#122. For concrete of grade M50, short-term modulus of elasticity will be nearly
#123. Joint filler used during highway construction are
#124. As per IS 456:2000, in limit state method of design, maximum strain in concrete at the outermost compression fibre in bending is taken as
#125. Which of the following is used for measurement of local velocities of fluid flowing through pipe?
#126. For a laminar flow between two parallel fixed plates, maximum velocity observed is 3 m/s. Average velocity of the flow will be
#127. A king closer is
#128. Carbon content of steel is increased. Which of the following parameters of steel will be reduced?
#129. In a tree, the cambium layer is situated between
#130. If 1% solution of a sewage sample is incubated for five days at 20 °C and depletion of oxygen was found to be 7 ppm, B.O.D of the sewage is
#131. Deciduous trees are having
#132. The total unit weight of soil is 22 kN/m³. The specific gravity of soil particles is 2.67 and the water content of the soil is 10%. The dry unit weight would be
#133. A 30 m chain is found to be 0.5 m too short throughout the measurement. If the distance measured is recorded as 300 m, the actual distance measured will be
#134. The fore bearing of a line is S39°42’E (no local attraction is there), the back bearing of the line will be
#135. Average annual rainfall recorded over six rain gauge stations is 100 cm and standard deviation from mean is 20 cm. For a 10% error in the estimation of mean rainfall, the optimum number of rain gauges required is
#136. Property of soil by virtue of which loss in shear strength caused due to remolding is recovered with time is known as
#137. A plate of thickness 0.010 mm, distant from a fixed plate, moves at 10 cm/s and requires a force of 1 N per unit area i.e. 1 N/mm² to maintain this speed. What would be the fluid viscosity between the plates?
#138. Deflection at the free end of a prismatic cantilever beam of length L, modulus of elasticity E and moment of inertia I, under load P at the free end will be
#139. Which of the following will be significant in case of fluid flows where compressibility effects are predominant?
#140. Objectives of seasoning are
#141. If the load stresses are 24 kg/cm², warping stresses are 30 kg/cm² and frictional stresses are 25.5 kg/cm², then what would be the value of critical stresses combination (in kg/cm²) at edge region during summer mid-day?
#142. Find the coefficient of permeability of a soil sample, if the value of hydraulic gradient is 6 and area of cross section is 50 cm². Also the quantity of water equal to 600 ml passed down in 10 minutes under an effective constant head of 40 cm.
#143. On the basis of geology of area, if clayey foundation is there then the dam will be
#144. If the specific gravity and voids ratio in a soil sample are G and e respectively, the (critical) hydraulic gradient i is represented by
#145. The coefficient of compressibility of soil is the ratio of
#146. Coarse grained soils are best compacted by
#147. The rise of water table below the foundation influences the bearing capacity of soil mainly by reducing
#148. The maximum differential settlement in isolated footings on clayey soil should be limited to
#149. Lime stabilization is very effective in treating
#150. The ratio of settlement at any time ‘t’ to the final settlement is known as
#151. A bar L metre long and having its area of cross-section A is subjected to a gradually applied tensile load W. The strain energy stored in the bar is
#152. The radius of gyration of a rectangular section (Depth D, width B) from a centroidal axis parallel to width is
#153. Slenderness ratio of a long column is
#154. A rigid jointed plane frame is stable and statically determinate if (m = number of members, r = reaction components, j = number of joints)
#155. A cantilever ABC is fixed at A (AB = 2 m, BC = 2 m). It carries a 2 T downward point load at B and an anticlockwise couple of 4 T·m at the free end C. The BM of the cantilever at A is
#156. The point of contraflexure occurs in
#157. Rate of change of angular momentum is equal to
#158. Four columns of a building are to be located within a plot size of 10 m × 10 m. The expected load on each column is 4000 kN. Allowable bearing capacity of the soil deposit is 100 kN/m². The type of foundation best suited is
#159. A beam of square cross-section with side 100 mm is placed with one diagonal vertical. If the shear force acting on the section is 10 kN, the maximum shear stress is
#160. If the length of a simply supported beam carrying a concentrated load at the centre is doubled, the deflection at the centre will become
#161. The following statements are related to bending of beams: I. The slope of the bending moment diagram is equal to shear force. II. The slope of shear force diagram is equal to load intensity. III. The slope of curvature is equal to flexural rotation. IV. The second derivative of the deflection is equal to curvature. The only false statement is
#162. The ratio of the theoretical critical buckling load for a column with fixed ends to that of another column with the same dimension and material, but with pinned ends is equal to
#163. The effective stress friction angle of a saturated cohesionless soil is 43°. The ratio of shear stress and normal effective stress on the failure plane is
#164. Which one of the following is categorized as a long term loss of prestress in a prestressed concrete member?
#165. A rectangular open channel of width 5.0 m is carrying a discharge of 100 m³/s. The Froude number of the flow is 0.8. The depth of flow (in m) in the channel is
#166. A bar of dia. D embedded in a concrete block with a pull-out force P applied to it. The length of embedment is L and τbd is bond strength and fy is tensile strength of bar. Which one of the following represents the max. value of P?
#167. A weight W hangs from two strings attached to a horizontal ceiling at A and B (AB = 5 m). The string from A (tension T1) is 3 m long and the string from B (tension T2) is 4 m long, meeting at the load. Which of the statements is true?
#168. Beam AB (4 m long, pinned at A) carries an 80 kN load at 3 m from A and rests at B on a roller placed on the overhanging end of a second beam; the second beam is supported on a roller at C and a pin at D, with the overhang (B to C) = 0.5 m and CD = 4 m. The reaction at support C is
#169. As per IS:800 (1984), the max. deflection in a beam should not exceed
#170. The maximum shear stress of steel beam should not exceed
#171. The permissible stress in axial compression depends mainly upon
#172. A tension member consists of a pair of angles placed back to back on the same side of gusset plate. The value of k for calculating net area (IS 800:1984) is given by
#173. In plate girders (mild steel), vertical stiffeners are required when the ratio of clear depth of web (d) to web thickness (t)
#174. Diagonal tension in a beam
#175. In limit state method of design, the maximum strain in steel at failure is
#176. If in a concrete beam the modular ratio is m, ratio of stress in steel to concrete is r, and effective depth of beam is d, then the depth of critical N.A. of beam is
#177. Which of the following statements is incorrect?
#178. The minimum eccentricity for design of column as per IS-456-2000, where L is unsupported length and D = lateral dimension, is
#179. A vertical triangular area with vertex downward and altitude ‘h’ has its base lying on the free surface of a liquid. The centre of pressure below the free surface is at a distance of
#180. An increase in metacentric height (i) increases stability (ii) decreases stability (iii) increases comfort for passengers (iv) decreases comfort for passengers. The correct answer is
#181. Stream lines and path lines always coincide in case of
#182. A pitot static tube is used to measure the velocity of water in a pipe. The stagnation pressure head is 6 m and static pressure head is 5 m. Calculate the velocity of flow assuming the coefficient of tube equal to 0.98.
#183. Two pipes of same length and diameter ‘d’ and ‘2d’ respectively are connected in series. The diameter of an equivalent pipe of same total length is
#184. If the depth of flow in a channel is 1 m and velocity of flow is 2 m/sec, then the velocity with which an elementary wave can travel upstream is
#185. A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels in the reservoirs is 8 m. The Darcy Weisbach friction factor of pipe is 0.04. Accounting for frictional, entry and exit losses, the velocity in the pipe (in m/s) is
#186. Hydraulic radius is equal to
#187. The ruling gradient in a hill road is 6%, and a horizontal curve is provided for a radius of 75 metres. The compensated gradient of the road will be
#188. Road roughness is measured using
#189. The super-elevation to be provided in horizontal curves of radius R in hill roads (as per IRC), where V is the speed in kmph, is
#190. For a vehicle moving with speed of 80 km per hour, the brake reaction time, in ordinary case, is
#191. If L is the length of moving vehicle and R is the radius of curve, the extra mechanical width b to be provided on horizontal curve (per lane) is
#192. For a given discharge, the efficiency of sedimentation tank can be increased by
#193. Disinfection (chlorination) efficiency is
#194. For the same solid content, if the quantity of sludge with a moisture content of 98% is X, then the quantity of sludge with moisture content of 96% will be
#195. Following processes are used in a water treatment plant: Rapid Mixing (RM), Flocculation (F), Primary Sedimentation (PS), Secondary Sedimentation (SS), Chlorination (C), Rapid Sand Filtration (RSF). The correct order of these in a water treatment plant is
#196. Match the parameters with their desirable limits (mg/l): 1. Nitrate, 2. pH, 3. Iron, 4. Dissolved solids, 5. BOD with A. 0, B. 0.3, C. 6.5 to 8.5, D. 45, E. 500
#197. The volume of one bag (50 kg) of cement is
#198. Inert material in cement concrete matrix is
#199. The first compound to be formed in the manufacturing of cement is
#200. The total amount of water required for hydration of cement and to fill the gel pores is

